LaCie 4TB 2big USB 3.0 Manual de usuario Pagina 17
- Pagina / 37
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
LaCie 2big USB 3.0 • DESIGN BY NEIL POULTON RAID
User Manual page 17
Fast SafeJBOD
Confirm
USB 3.0
DESIGNED BY NEIL POULTON
3.2. Changing the RAID Mode
See section 3. RAID to become familiar with the levels of RAID
available to the 2big USB 3.0 before following the steps below.
IMPORTANT INFO: Changing the level of RAID will require
that you format the LaCie 2big USB 3.0. Please back up any
data stored on the LaCie 2big USB 3.0 before following the steps
below.
CAUTION: Your LaCie 2big USB 3.0 comes preconfigured in
RAID 0, which provides faster transfer rates and allows access to
the whole storage capacity. Unlike RAID 1, it does not provide
any security. If a drive fails, all data will be lost. If you are con-
cerned about data security, LaCie highly recommends changing
your 2big USB 3.0 to RAID 1. See section 3.1. About RAID Modes,
for more information.
Note the rectangular slot located between the two drive trays on
the back of the 2big USB 3.0 (Fig. 13). This is the RAID selection
switch. There is a switch inside the slot used for selecting the level
of RAID:
✦ Left = RAID 0 (FAST)
✦ Center = JBOD
✦ Right = RAID 1 (SAFE)
The RAID confirmation button is below the RAID selection switch;
a small circular slot with a button inside (Fig. 13).
The 2big USB 3.0 must be turned on to change the level of RAID.
Attach the power cable if it is disconnected. Switch on the 2big
USB 3.0 by pressing the front LED button. The front LED will blink
as the
RAID boots. It will become solid blue when ready.
To change the RAID mode:
1. Unmount the 2big USB 3.0 volumes from your computer
(2.3. Disconnecting Your Hard Drive) and disconnect the
interface cable.
2. To modify the level of RAID, use the 2-in-1 tool to slide the
switch to the desired position (Fig. 13).
3. Validate the new level by pushing the RAID confirmation
button with the 2-in-1 tool (Fig. 13). The 2big USB 3.0 will
turn off to signal the RAID change confirmation.
4. Reattach the USB 3.0 cable to your computer. The 2big
USB 3.0 will start automatically if the computer is on. The
new RAID level has been successfully configured.
5. Format the disks. See section 3.4. Formatting and Partition-
ing.
continued on the next page>>
Fig. 13
RAID Selection Switch
Tool
RAID Confirmation Button
- Table of Contents 1
- User Manual page 2 2
- Health and Safety 3
- Precautions 3
- General Use 3
- 1. Introduction 4
- User Manual page 5 5
- 1.2. Box Content 6
- 1.3. Views of the Drive 7
- User Manual page 8 8
- 1.4. Cables and Connectors 9
- User Manual page 10 10
- User Manual page 11 11
- 2.2. Turn the Drive On 12
- User Manual page 13 13
- 3.1. About RAID Modes 14
- User Manual page 15 15
- User Manual page 16 16
- 3.2. Changing the RAID Mode 17
- User Manual page 18 18
- User Manual page 19 19
- User Manual page 20 20
- User Manual page 21 21
- User Manual page 22 22
- User Manual page 23 23
- User Manual page 24 24
- User Manual page 25 25
- User Manual page 26 26
- User Manual page 27 27
- User Manual page 28 28
- User Manual page 29 29
- User Manual page 30 30
- User Manual page 31 31
- 4. Troubleshooting 32
- 4.1. LED Status Indicators 33
- User Manual page 34 34
- User Manual page 35 35
- 6. Warranty Information 37
Relacionado con productos y manuales para Arrays de discos LaCie 4TB 2big USB 3.0
(47 paginas)Canon PIXMA iP100 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Drukarki Canon PIXMA iP100.
Dostarczamy 2 pdf podręczników Canon PIXMA iP100 do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentarios a estos manuales